Long Island Shooters Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-18 of 31 Results
  1. Off Topic Lounge Chit-Chat
    I'm looking for someone to remove a brick Chimney - basement to roof is 2 stories, 18 Inch square, and already exposed. Messy heavy job I don't want to do by myself!
  2. AR Rifles
    So I'm trying to remove the bolt catch roll pin. I've tried a 3/32 punch that I ground down like the one on brownells but I just bent the punch and cracked it off. I'm trying to drive it to the back towards the stock but it hasn't even budged. Any ideas before I take it to a gunsmith?
  3. Bolt Action Rifles
    So, I bought a nice surplus 8mm FN mauser. All looked good until I checked the head spacing ... It was terrible, the bolt handle stays vertical ... Took it appart it turns out soneone just screwed in a german k98 barrel in. I need to fix it now. I'm not into machining the barrel at all, I'm just...
  4. Car / Truck talk
    Anyone have one of these tools to lend. Long story, just gotta get one lug nut off of my Jeep.
  5. Off Topic Lounge Chit-Chat
    Need a house done in Garden City tonight ASAP. Anyone working in that area want a job? Pm me for details
  6. Vendor Deals
    Hey everyone, We are running a special for LIF members!! $540 for a full load of household junk. Our vehicles hold 15 cubic yards. Two workers come to the house to load and haul away. http://www.jiffyjunk.com
  7. Semi-Auto Rifles
    Anyone here successfully remove a damaged/ stuck LR308 Bolt Catch screw ? I ordered a Phase 5 Ambi Bolt Release and I cannot, with the tools readily available to me, remove the screw. The head is stripped and it is a difficult spot to work in. I tried a number of work arounds but it is not...
  8. DIY - Home Improvements - More
    I recall that there is a member here that does junk removal / home clean outs. Anyone know who that is? Thanks n advance.
  9. Semi-Auto Handguns
    painted lower with Krylon,want to strip it back,suggestions?type remover... Sent from my DROID X2 using Tapatalk 2
  10. Semi-Auto Handguns
    Step one: remove pin. Step two: gently pull grips from frame allowing the cheap, brittle plastic to explode in to pieces. Step 3: crack open a cold one.
  11. Rifles
    I have a 1926 mosin that I have had at the range a handful of times. It was having accuracy issues and I thought it was due to weak grooves in the barrel. Turns out the rifle is just beyond dirty. I have foamed the barrel 3 times now sitting overnight each time and the patches still come out...
  12. Car / Truck talk
    Anyone know someone good local? Can a small ding on a door line be fixed? A rock must have hit it or somthing on the parkway. Hard to find but I see it every time I walk by!!
  13. DIY Projects and Builds
    My Swiss K-31 has a scope mount installed. I broke the main screw on the mount last two weeks. I was able to get a replacement screw from Accumounts, however I couldn't get the broken part out. It may be a simple process but I don't have proper tools. Does anyone know there's any shop on the...
  14. Motorcycles
    Hey ladies and gents, I have a slow leak on the rear tire of my Vulcan 900. I think it might be a bad valve seal as the tire holds pressure all day and only looses when I am riding. I plan on trying the soapy water check to be sure. If it is the valve seal, and as always money is tight, I would...
  15. Off Topic Lounge Chit-Chat
    got a **** living under my backyard shed. want it out before it spawns and becomes uber nasty and territorial. is it worth it to get a service to remove or to buy a trap and do it myself? amazon sells em for $50 or so. whats the average cost of someone doing the dirty work for me? did a...
  16. Milsurp Rifles
    Ok a buddy of my just put a big ding in his pride and joy and ask me how to get it out. Well I was wondering the something as my SKS stock looks like it was drop in a cement mixer with a dozen cinder blocks  for a day. So how would one raise a dent out of a wood stock.
  17. Semi-Auto Shotguns
    Ok Guys Have a question. I just dug my Father in-laws 11-87 Deer gun out of his safe for a little range time. I am sure it hasn't been used in about 10 years and wanted to give it a good once over prior to taking it out. But of course I am having an issue getting barrel out. It seems like it...
  18. Off Topic Lounge Chit-Chat
    Hey everyone, After being plagued with pain and endless Dr. Appointments, it turns out I have to go for surgery for my gallbladder. Have any of you had this done?? I just want to know what to expect. Any pain after, recovery time, that kind of stuff. Any info would be great.
1-18 of 31 Results