Search Results for ‘rear’

Anyone know how the 4 clicks on the rear sites relates to yardage ? Its been thirty years I just can't remember. Bought .308 ammo today Going to range Friday I'm going to be such a newbie its been So long. Very strange feeling. Bet most people their never fired a m60 or m49 grenade launcher.

Anyone know how the 4 clicks on the rear sites relates to yardage ? Its been thirty years I just can't remember. Bought .308 ammo today Going to range Friday I'm going to be such a newbie its been So long. Very strange feeling. Bet most people their never fired a m60 or m49 grenade launcher.

The drift adjustable rear sight that comes with this rifle is pretty poor (really non adjustable for windage). Mine falls out if I try to adjust it. Does anyone have suggestions on a good replacement?

I am planning to buy me P223 scope sometime soon, but for now, I was surfing online for rear and front Magpul MBUS Gen 2 Sight for my new AR. I see many different prices. Ebay, a set for $30 , other one a set for 49$, some single $54-59 each! I'm just scratching my head.. I would order the...

Good Morning all, I have a buddy that just picked up his first Glock and it seems the rear sight needs to be adjusted. its hitting way left at 15 yards. So 1st question does anyone have a rear sight adjustment tool they would be willing to lend me? As I am the one that would be doing the work...

I installed TSR100 tech sights on my Ruger 10/22 and have it zeroed in. I noticed that the rear sight aperture is almost all the way to the left side with just a few clicks left. Is this normal?

I need some help on where I can get a replacement sight for my AK47. The hexhead screw that secures the slide part of the sight somehow became stripped and can't be removed. I've already checked most of the sights and I can't for the life of me find the part I need. Any suggestions would be...

LIF I have another dilemma. I'm basically reverting my ruger 10/22 to Ny compliant. I previously had it loaded into a gorgeous Archangel 556 stock. Taking off the stock I realized that I previously un mounted the rear sight( in order for it to fit the stock) , and now it's gone. Here comes the...

Any tips to make is easy. I have it jacked up and supported safely.

Looking at daweson precision front and rear fiber optics. Anyone have that  combo on a pistol, if so how do yah like the front matched with the rear fibers? THANKS!!

Hey ladies and gents, I have a slow leak on the rear tire of my Vulcan 900. I think it might be a bad valve seal as the tire holds pressure all day and only looses when I am riding. I plan on trying the soapy water check to be sure. If it is the valve seal, and as always money is tight, I would...

Will sights from the M&P 9 and 40 be the same...aftermarket like the Trijicon or Novak.....or is the 22 on its own?

I am trying to remove the rear sight from my Mosin, but 2 of the 3 pins won't even budge. I assume the sight and the pins have been soldered. Can I use the regular blue can Bernzomatic torch to heat it up?

Was trying to install my stock the other day and get the end plate on. Had a little issue with the rear takedown pin figured I'd give it another shot or if anyone has suggestions. Got in just fine, locked the castle nut down and tested it out. Pin went into the open position but would not for...

I had some time and extra .036 Aluminum, so which one goes in my car window?

Not sure how many of you guys started doing your builds but Spikes made it a little easier for you. Spikes tapped out a hole for a set screw for the rear takedown detent spring. All you will need is 1/8-inch 4-40 Allen head set screws and a 0.5mm Alen wrench. (Please note the following pics...

I was removing my G19 from the safe and I inadvertently hit the rear sight against the lip on my safe. It made a small mark on the sight and now I'm concerned the sight may have moved. I don't see anything obvious but are the factory sights pretty secure?

My new upper will be here tomorrow, and this is my first build that has a front sight post. Previously, I have purchased matching sets of front and rear sights, but I only need the rear this time. I am looking at the A.R.M.S. #40L, any thoughts? I am open to suggestion. I'm also open to...

putting a brasstacker mount on one of my mosins but one of pins on rear sight won't budge using just a punch. I guess it's soldered even though it shouldn't have been. Any suggestions short of using a torch? lubricants etc...

Somehow, the Schumer fairy managed to steal my rear takedown detent spring! Does anyone have a spare one lying around, or know where I can get one for cheap?